This article mainly introduces:

Cameroon hydraulic cylinder,reciprocating cylinder manufacturer,reciprocating cylinder

(Cameroon reciprocating cylinder,produced by Hengyu Hydraulic Cylinder Factory）

reciprocating cylinder are widely used in Cameroon，because of high work efficiency，excellent fatigue and impact resistance，no need for deceleration device.So our company has designed reciprocating cylinder for customers from Cameroon.

Introduction to reciprocating cylinder:

The pressure of the sliding surface of the reciprocating cylinder piston is too large, resulting in sintering. The piston tilts due to the weight of the piston rod, resulting in the phenomenon of non-stiffness, or the pressure of the sliding surface of the piston rises due to the action of the transverse load, which will cause sintering. In the design of the reciprocating cylinder must study its working conditions, the length of the piston and bushing and the size of the clearance must be fully paid attention to.

The repair method of reciprocating cylinder wear: 1. Metal repair material is applied to the scratched surface; The first layer should be thin, uniform and fully covered with the scratched surface to ensure the best adhesion between the material and the metal surface, and then apply the material to the entire repair site and press repeatedly to ensure that the material is filled and reaches the required thickness, so that it is slightly higher than the surface of the guide rail; 2, the material at 24℃ to fully achieve the performance of 24 hours, in order to save time, can be through the tungsten halogen lamp to increase the temperature, the temperature rises 11℃, the curing time will be reduced by half, the best curing temperature 70℃; 3. After the material is cured, use a fine grinding stone or a scraper to repair and smooth the material higher than the surface of the guide rail, and the construction is completed.

When the reciprocating cylinder is in use, measures should be added to prevent the intrusion of pollutants. Effective measures should be taken to control the intrusion of pollutants, such as installing high-efficiency air filters in the tank breathing holes, new oil must be filtered, etc., but also must improve the anti-pollution ability of the reciprocating cylinder itself. In the seriously polluted environment, it is more important to pay attention to, such as the underground oil reciprocating cylinder should use fluorine rubber (FRM) and nitrile rubber (NBR) dust ring, and the ground mechanical reciprocating cylinder should use nitrile rubber dust ring; The filter device is added to the oil inlet of the reciprocating cylinder of the dump truck, construction machinery, work platform and other equipment, and in order to reduce the oil inlet resistance, the flow area should be increased as much as possible, which can effectively reduce the particle pollution from the system.

The reciprocating cylinder is a hydraulic actuator that converts hydraulic energy into mechanical energy and does linear reciprocating motion (or swinging motion). It is simple in structure and reliable in operation. When it is used to achieve reciprocating movement, the deceleration device can be eliminated, and there is no transmission gap, and the movement is smooth, so it is widely used in various mechanical hydraulic systems. The output force of the reciprocating cylinder is proportional to the effective area of the piston and the pressure difference between the two sides; The reciprocating cylinder is basically composed of reciprocating cylinder and reciprocating cylinder head, piston and piston rod, sealing device, buffer device and exhaust device. Buffer device and exhaust device depending on the specific application, other devices are essential.

Answers to some questions about reciprocating cylinder:

The diameter of the cylinder is 180mm and the pressure is 14mpa. How many tons can the cylinder hold?
Calculate the area of the cylinder, 3.14*9*9=254.34 square centimeters, take the approximate number of engineering, 1 mpa pressure is about 10 kg per square centimeter, 14 mpa pressure is 140 kg per square centimeter, that is 254.34*140=35607.6 kilograms, it can be known that the cylinder can be about 35 tons in theory.

How many tons can a 10mpa cylinder with a diameter of 100 hold up?
About 8 tons. Algorithm: Cylinder cross-sectional area = π* (100/2) ^2=3.14*2500=7850 square mm = 0.00785 square meters pressure = pressure * Cross-sectional area = 10000000Pa*0.00785 square meters = 78500 n mass = pressure /g = 78500 N ÷9.8 n/kg = 8010 kg = 8.01 Tons.