This article mainly introduces:

Japan hydraulic cylinder,servo cylinder manufacturer,servo cylinder

(Japan servo cylinder,produced by Hengyu Group）

servo cylinder are widely used in Japan，because of powerful torque，clever hydraulic energy conversion，simple structure and reliable operation.So our company has designed servo cylinder for customers from Japan.

Introduction to servo cylinder:

If it is found that the servo cylinder lubrication is poor or the servo cylinder bore processing is abnormal, it is necessary to feedback the situation to the manufacturer, because the piston and the servo cylinder, the guide rail and the piston rod have relative movement, if the lubrication is poor or the servo cylinder bore is abnormal, it will aggravate the wear and reduce the straightness of the servo cylinder center line. In this way, when the piston works in the servo cylinder, the friction resistance will be large and small, resulting in slip or crawling. The solution is to repair and grind the servo cylinder first, and then prepare the piston according to the matching requirements, repair and grind the piston rod, and configure the guide sleeve.

If the servo cylinder is sliding or crawling (stop and go), check whether there is any astringency inside the servo cylinder. The internal parts of the servo cylinder are improperly assembled, the parts are deformed, worn or the shape and position tolerance is excessive, and the action resistance is too large, so that the piston speed of the servo cylinder changes with the different stroke position, and there is slip or crawl. Most of the reasons are due to poor assembly quality of parts, surface scars or sintered iron filings, so that the resistance increases, the speed decreases. For example, the piston is different from the piston rod or the piston rod is bent, the servo cylinder or the piston rod is offset from the mounting position of the guide rail, and the sealing ring is too tight or too loose. The solution is to repair or adjust, replace damaged parts and remove iron filings. At the same time, check whether the lubrication is good or whether the servo cylinder bore processing is out of whack. Because the piston and servo cylinder, guide rail and piston rod are relative If the servo cylinder is crawling seriously, check whether air has entered the hydraulic system. Air compression or expansion can cause the piston to slip or crawl. The exclusion measures are to check the hydraulic pump, set up a special exhaust device, and quickly operate the exhaust several times in the full stroke. Check the seals at the same time, because the quality of the seals is directly related to slippage or crawling. When the O-ring is used under low pressure, compared with the U-ring, it is easy to slip or crawl because of the higher surface pressure and the larger difference between static and static friction resistance. The surface pressure of the U-shaped sealing ring increases with the increase of pressure, although the sealing effect is correspondingly improved, but the difference between static and static friction resistance is also larger, the internal pressure increases, affecting the rubber elasticity, due to the increase in the contact resistance of the lip, the sealing ring will tip over and the lip elongation, and it is also easy to cause slip or crawling servo cylinder weight composition and calculation. The weight of the servo cylinder is composed of the servo cylinder diameter, the outer diameter and weight of the servo cylinder, the rod diameter, and the weight of the accessories, so in calculation, it is to add all these together to get the specific value. However, if there are special circumstances, it may be calculated separately. This work can be carried out by yourself, but it can also be carried out by professionals, so that mistakes can be avoided.

servo cylinder piston sealing is best to use Yx ring, polyurethane and polytetrafluoroethylene sealing material combination, can significantly improve the sealing performance: (I), reduce friction resistance, no crawling phenomenon; (ii) Have good dynamic and static sealing, wear resistance, long service life; (iii) The installation groove is simple, and the disassembly is simple.

The repair method of servo cylinder wear: 1. Metal repair material is applied to the scratched surface; The first layer should be thin, uniform and fully covered with the scratched surface to ensure the best adhesion between the material and the metal surface, and then apply the material to the entire repair site and press repeatedly to ensure that the material is filled and reaches the required thickness, so that it is slightly higher than the surface of the guide rail; 2, the material at 24℃ to fully achieve the performance of 24 hours, in order to save time, can be through the tungsten halogen lamp to increase the temperature, the temperature rises 11℃, the curing time will be reduced by half, the best curing temperature 70℃; 3. After the material is cured, use a fine grinding stone or a scraper to repair and smooth the material higher than the surface of the guide rail, and the construction is completed.

Answers to some questions about servo cylinder:

How to remove the air in hydraulic cylinder?
Connected the cylinder to the system, and reciprocating move with full stroke several times, then the air can be eliminated . There is also a clunky method as follows: first remove the rod cavity oil pipe, connect the rodless cavity oil circuit to extend all the cylinders, and then remove the rodless cavity oil pipe, connect the rod cavity oil pipe and withdraw all the cylinders, and then connect the rodless cavity oil pipe, so that there is no air in the cylinder.

What are the standard cylinder models for hydraulic cylinders?
National standard GB/T2348-1993 specifies the hydraulic cylinder inner diameter series, you can check GB/T2348-1993 relevant regulations.