This article mainly introduces:

UAE hydraulic cylinder,tension cylinder manufacturer,tension cylinder

(UAE tension cylinder,produced by Hebei Hengyu company）

tension cylinder are widely used in UAE，because of clever hydraulic energy conversion，simple structure and reliable operation，excellent temperature resistance.So our company has designed tension cylinder for customers from UAE.

Introduction to tension cylinder:

Before the tension cylinder is removed, the system should be unloaded, the loop pressure is zero, the oil source should be cut off, and the oil port should be blocked after the oil port distribution pipe is loosened.

If the tension cylinder operation failure, you can start from these aspects to troubleshoot: (1) the hydraulic system control pressure is too low. The throttling resistance in the control line may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is disturbed. At this time, the control pressure source should be checked to ensure that the pressure is adjusted to the specified value of the system; (2) Air enters the hydraulic system. Mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced. (3) The initial action of the tension cylinder is slow. In the case of low temperature, the hydraulic oil viscosity is large, poor flow, resulting in slow tension cylinder action. The improvement method is to replace the hydraulic oil with better viscosity and temperature performance If the tension cylinder is weak and cannot push the load, please check the internal leakage problem. The internal leakage of the tension cylinder includes the leakage caused by excessive wear of the tension cylinder block seal, the piston rod and the seal cover seal and the piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time. The main cause of excessive piston seal wear is improper adjustment of the speed control valve, resulting in excessive back pressure and improper seal installation or hydraulic oil contamination. The second is that foreign bodies enter the assembly and the quality of sealing materials is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and tension cylinder, and the phenomenon of "pulling the tension cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operations should be done according to the installation instructions.

When the tension cylinder wear is serious, you can try to use an alloy scraper to shave grooves with a depth of more than 1mm on the surface of the slip injury, then clean the grooves with acetone, apply the adjusted TS311 anti-wear repair agent on the polished surface with the tension cylinder inner diameter copying plate, and scrape it flat vigorously to ensure compaction and higher than the inner surface of the tension cylinder. After curing, polish to leave a finishing margin. Finally, the overall size, shape tolerance and roughness of the tension cylinder can meet the requirements by grinding. However, the life and reliability of this repair tension cylinder are not high.

In use, the tension cylinder should try to avoid the friction iron powder or iron filings formed by buffering the plunger. When the matching gap of the buffer device is small and the transverse load on the piston rod is large, the sintering phenomenon may be caused. These friction iron powder or the metal fragments that have fallen off as a result of sintering will remain in the tension cylinder.

Answers to some questions about tension cylinder:

How does the one-way solenoid valve control the hydraulic cylinder circuit?
If your cylinder is single-acting, you can use a one-way solenoid valve, such as some lifting platform hydraulic cylinder, the support valve used is one-way (two-position tee), that is, the cylinder extends out by the oil pressure top, the cylinder retracted by its own weight.

Is there a national standard for the testing of hydraulic cylinders?
Generally speaking, the cylinder test is carried out according to JB/JQ20302 Allowable leakage of cylinder in pre-factory leakage test. GB2879 hydraulic cylinder piston and piston rod dynamic seal groove type, size and tolerance. GB6578 hydraulic cylinder piston rod dust ring groove type, size and tolerance. GB7938 hydraulic cylinder and cylinder nominal pressure series, etc.